Woodworking Carol

A friend emailed this to me:

(Sung to the tune of Joy to the World)

Joy in the shop
The dovetails fit
Was it luck
or this new saw?
Let every tool prepare some room
and I'll get on the net and I'll get on the net
and order and order some more new tools!

Merry Christmas!

May you find a new set of Lie Nielsen chisels in your stocking

and lots of time in the new year to use them!

3 Ways to Make Dowels

You can buy wood dowels in common species like walnut, cherry, and pine, but if you need a dowel in an uncommon species, or if you're making authentic reproductions, or you just like to try different techniques, here are three ways to make them.

One: Use a beading plane to round over both sides of a board, then snap off the dowel. Shave the rough, snapped-off edge with a block plane or chisel. Match the thickness of wood with the diameter of the bead so the dowel is perfectly round.

Two: Use a block plane to round over a square blank and eyeball it as you go. This works great if you like that imperfect, handmade look, like you find in PA German furniture. (If you take your time, though, you can make very precise dowels with this technique.)

















Three: Use a dowel plate (mine is from Lie-Nielsen). Make sure you cut your blank very close in size to the final dowel diameter, otherwise, it's likely to split as you tap it through. Use a chisel to taper the leading end. Dowel plates work best with short pieces of wood.

Two Turtle Dogs

Daisy and Rosie in their Christmas frocks.

Shellac Gone Bad

Shellac is an excellent finish, not necessarily for table tops (because it's not very protective), but for other projects that won't see too much traffic. A couple of things that make shellac so great are its ease of application and the speed at which it dries. However, shellac does have a relatively short shelf life. If you mix your own, you have at most 6 months until it goes bad. If you use premixed shellac, like Zinsser, you have about one year to use it once you open the lid.

I found out the hard way not to push my luck.

I was asked to build some decorative boxes for my church that needed to be ready in time for a very important day. Knowing I was going to use shellac for the finish, I allowed only one day to apply the finish—the day before the important event. After applying 3 coats, I wondered where all the blotchy, shiny spots were coming from. They would rub out momentarily with steel wool, only to reappear a short time later.

Ugh. All that careful construction and the finish made the boxes look horrible. I took them to the Woodcraft Store to consult my buddy, Dan the Finishing Guru, who immediately deduced that I had used old shellac. Friends, old shellac will never, ever, ever dry. It will always have blotchy, shiny spots and will completely undermine your meticulous craftsmanship.

Fortunately, there's another great thing about shellac—it's easy to remove! A little denatured alcohol dissolved all of it. So I mixed a fresh batch, applied several coats, rubbed out the finish the next morning, and had a whole 15 minutes to spare before the big event. Whew!

So how do you determine if your shellac has crossed over to the dark side? Brush some on a piece of wood. If, after 15 minutes, it's not completely dry and looks blotchy....throw-it-out!*

Do you see all of the tell-tale shiny spots at the top of my tool cabinet door?

Yeah, I'll fix that someday.

*Dan, the finishing guru, says to put a dollup of shellac on a piece of glass, let it sit overnight, and if you can press your fingernail into it the next day, mix up a fresh batch.

Workbench Book

If you're planning to build a workbench, I highly suggest reading Workbenches: from Design & Theory to Construction & Use, by Christopher Schwarz.

The title says it all. Chris includes plans to build both English and French workbenches, but more importantly helps you decide what style, wood, size and vises will work best for your type of woodworking. I can't say enough good things about this book; it's bound to be a classic.

Splined Miter Jig

If you want to build boxes with splined miters, using a jig like this along with your table saw makes the job easy.

The cradle is made of two boards attached at 45 degrees to two outer boards. Your box sits in the jig which rides along the table saw fence while the blade cuts a perfect kerf in each corner. Move the fence to make a second kerf in each corner if you like.

If you use a flat tooth blade, the bottom of the kerf will be flat and your miter key will fit right in. If you use an ATB (alternate top bevel) blade, you'll have a little clean up to do with a chisel in order to flatten the bottom of the kerf so the key fits snugly.

(I had trouble getting clear shots of the blades and yes, I know they desperately need to be cleaned. : )

Sometimes it's enough

I read an article this morning about a recently deceased local man who was a passionate woodcarver his entire life. He was born in 1922, served in WWII by parachuting behind enemy lines and blowing up bridges, witnessed the attack on Pearl Harbor, and of this event, wrote these words in his Bible: Hell is moving. We have all missed death 100 times this day. Amen.

His workshop was a converted chicken coop behind his house where he would sit for hours whittling whimsical characters and animals, often so engrossed in his project, he would work through dinner.

In the article, this is the sentence that really resonated with me and to which, I think, most woodworkers can relate: Arthritis stopped him from carving and whittling about four years ago, but he still shuffled to the wood shop with the help of a walker and sat among the pieces of wood and sawdust.

As I'm entering my busy season at work, I know that I probably won't be able to do any woodworkng until mid-March. But, during the busy months, I always seem to find a little time to at least sit in my shop or tidy up or open my tool cabinet and take out my handplanes. Sometimes it's enough to just be out there sitting among the wood.